Sink installation in Mount Pleasant, TX, fitted and sealed

Sink installation is the professional fitting of a new kitchen or bathroom sink in a Mount Pleasant, TX home. A new sink should sit level, drain cleanly, and never weep at the trap. NTP Plumbing installs kitchen and bathroom sinks across Mount Pleasant, TX — trap set, disposal connected, tested before we leave. Open 24 hours, Monday through Sunday.

New kitchen sink being installed in a Mount Pleasant, TX homeNew sinkTrap setTested dry
  • We test twiceSupply lines, then drain
  • We protect countersDrop cloths and pads
  • We haul it offOld sink goes with us
  • We explain firstBefore we cut anything

What our sink installation includes

Every sink installation job includes the labor and standard materials to remove the old sink, set the new one, connect the plumbing, and test it. If we find a problem under the cabinet, we tell you before we fix it. Here is what is covered.

New kitchen sink being installed in a Mount Pleasant, TX home
  • Old sink removal

    We disconnect the supply lines and drain, cut the old sealant, and lift the old basin out. The old sink goes with us, so you are not stuck trying to haul a cast iron sink to the curb.

  • New sink set and sealed

    We set the sink in silicone or mount it with the correct clips, level the basin, and seal the rim. Undermount and farmhouse sinks get the cutout checked against the template before anything is set.

  • Drain and supply connections

    We connect the drain, P-trap, supply lines, and shutoff valves. If the old valves are frozen or the supply lines are brittle, we replace them with new braided lines and quarter-turn valves.

  • Faucet install

    If you have a new faucet, we install it with the sink. We connect the sprayer, the supply lines, and the drain assembly, and check the aerator for debris before we turn the water on.

  • Full water test

    We run hot and cold water, fill the basin, and drain it while checking every connection with a flashlight. If anything drips, we fix it before we leave.

  • Cleanup and haul-off

    We wipe down the counter, clean the cabinet, and take the old sink and packaging with us. You get a working sink and a clean kitchen or bathroom when we walk out the door.

Homes and rentals

A kitchen sink and a bathroom sink install differently — one is the trap and the disposal, the other is the pop-up and the overflow — but the checks at the end are the same in a home and a rental. What changes is the access, the schedule, and who needs the paperwork for a sink installation job.

For homes and rentals

We install kitchen, bathroom, and utility sinks in houses and rentals. We work around your schedule and test every connection before we leave.

  • Cracked or leaking basin
  • Remodel sink swap
  • Frozen shutoff valves

For rentals and property managers

We handle sink installs in rental units. We schedule around tenant access and send photos of the finished work for the property file.

  • Kitchen sink install
  • Rental turnover swaps
  • Multiple units, one schedule

What sink installation in Mount Pleasant, TX actually involves

A plain-language look at what Sink Installation involves and when it is needed. The City of Mount Pleasant charges a $75 residential plumbing permit fee where a permit is required (inside city limits) — that is a City fee, not our price.

See how it works

Installing a sink means setting the basin level, sealing the strainer, connecting the trap and — in the kitchen — the disposal and dishwasher drain. Then the tap runs while we watch every joint: the strainer, the trap, the disposal connection and the supply lines. A sink that weeps at the trap on day one will rot the cabinet within a year, so the test matters as much as the fit.

Most installs in Mount Pleasant, TX are kitchen refreshes in Downtown homes and Southgate ranches, and finish work in Northwood, Stone Briar and Deer Park Estates new builds. In older homes the drain under the sink is often galvanised and the trap can be corroded; we check it while the old sink is out, because that is the only cheap moment to deal with it. Sink installation work follows the 2024 International Plumbing Code adopted by the city.

A sink install is a trap job with a basin on top of it.

New kitchen sink being installed in a Mount Pleasant, TX home
What it is
Removing an old sink and fitting a new one, with the trap, strainer and disposal connected.
When you need it
A cracked basin, a stain that will not clean, or a kitchen or bathroom remodel.
What to expect
A level basin, a clean drain, and a cabinet that stays dry.

How our sink installation process works

Every job follows the same five steps, whether it is a kitchen sink or a single bathroom vanity. You get a walk-through before we start and a water test before we leave.

  1. Walk-through and shutoff

    We look at the existing sink, the cabinet base, the shutoff valves, and the drain line. Then we shut off the water and protect the counter and floor. This tells us whether the old valves need replacing before we start.

    • Walk-through
    • Shutoff
    • Protect
    New kitchen sink being installed in a Mount Pleasant, TX home
  2. Remove the old sink

    We cut the silicone or release the clips, disconnect the supply lines and drain, and lift the old basin out. If the old drain line is corroded cast iron or the shutoff valves are frozen, we flag it before going further so there are no surprises.

    • Disconnect
    • Lift out
    • Flag issues
    New kitchen sink being installed in a Mount Pleasant, TX home
  3. Prep the cutout and fittings

    We clean the old sealant off the counter, check the cutout against the new sink template, and test-fit the basin. Supply lines, the P-trap, and the shutoff valves get checked or replaced here. A new sink install often needs new braided supply lines.

    • Clean cutout
    • Test-fit
    • Check valves
    New kitchen sink being installed in a Mount Pleasant, TX home
  4. Set and connect the sink

    We bed the sink in silicone or set the undermount clips, connect the faucet, supply lines, and drain, and tighten everything to spec. The P-trap gets aligned so it does not stress the drain stub. This is where a careful install saves you a callback.

    • Set sink
    • Connect drain
    • Tighten
    New kitchen sink being installed in a Mount Pleasant, TX home
  5. Water test and cleanup

    We run hot and cold water, fill the basin, and drain it while checking every connection underneath. If it is dry, we clean up, haul off the old sink, and walk you through what we did.

    • Water test
    • Cleanup
    • Haul off
    New kitchen sink being installed in a Mount Pleasant, TX home

Tools and methods we use on sink jobs

Move across a circle, or focus it and press Enter, for an illustrative thermal view of this sink installation photograph.

  • New kitchen sink being installed in a Mount Pleasant, TX home

    Pipe wrench

    Used to break loose old drain fittings and supply connections without rounding the nuts. We carry two sizes so we can work in tight cabinets.

  • Plumber cleaning a clogged drain in a Mount Pleasant, TX home

    Drain snake

    Clears clogs in the trap arm and branch line before the new sink goes in. A clogged drain is the most common reason a new sink drains slow.

  • Plumber replacing old pipe with new PEX in a Mount Pleasant, TX home

    PEX crimping tool

    Makes secure connections on PEX tubing when we replace a supply line or shutoff valve. The crimp ring gives a mechanical connection that holds pressure.

  • Plumber soldering a copper pipe joint under a kitchen sink in a Mount Pleasant, TX home

    Tubing cutter

    Cuts copper and PEX clean and square so fittings seat properly. A square cut is the difference between a leak-free joint and a drip.

  • NTP Plumbing technician with tools at a Mount Pleasant, TX home

    Pressure gauge

    Checks the house water pressure before we connect the new sink. High pressure can stress supply lines and cause leaks at the fittings.

Thermal views are illustrative, generated from photographs of sink installation work in Mount Pleasant, TX.

Methods

  • Sewer camera

    Used when a sink backs up and we suspect a bigger line problem. The camera shows root intrusion or a collapsed pipe before we recommend a repair.

  • 2024 International Plumbing Code adopted by the City of Mount Pleasant (Ordinance 2026-2, effective 20 January 2026)

    We follow IPC rules on trap arms, venting, and shutoff placement. That means the drain is vented correctly.

  • Template-based cutout

    Undermount and farmhouse sinks come with a template. We measure the cutout against it before cutting, which prevents an oversized opening that will not seal or a small one that cracks the counter.

  • Two-stage water test

    We test the supply lines under pressure first, then fill and drain the basin to test the drain and P-trap. Two stages catch both supply-side and drain-side leaks before we leave.

  • Material-matched connections

    We use copper pipe, PEX tubing, PVC pipe, or CPVC pipe depending on what the run calls for. push-to-connect and expansion fittings are used where they make sense, and we never mix materials without the right transition fitting.

When Mount Pleasant homeowners call for sink installation

New kitchen sink being installed in a Mount Pleasant, TX home

Kitchen refresh

A remodel needs a new sink and faucet on a fresh countertop.

We set the basin level, sealed the strainer, connected the trap and disposal, and tested every joint with the tap running.

Outcome: A solid sink with a dry cabinet underneath.

New kitchen sink being installed in a Mount Pleasant, TX home

Bathroom vanity

A vanity replacement needs a new basin sink.

We fitted the sink, connected the trap and the pop-up, and checked the supply lines while the cabinet was open.

Outcome: A finished vanity with dry connections.

New kitchen sink being installed in a Mount Pleasant, TX home

Cracked basin

The old sink is cracked and weeps into the cabinet.

We removed the sink, checked the trap underneath, and set the new one on a sound base.

Outcome: A dry cabinet and a basin that holds water.

New kitchen sink being installed in a Mount Pleasant, TX home

New build finish

A new-build kitchen needs its sink set.

We installed the sink on the new countertop, connected the disposal and dishwasher drain, and tested it all.

Outcome: A finished kitchen, tested and dry.

New kitchen sink being installed in a Mount Pleasant, TX home

Rental turnover

A rental kitchen needs a new sink before the next tenant.

We coordinated with the property manager, installed the sink and a new trap, and left the old one for disposal.

Outcome: A fresh kitchen sink ready for move-in day.

New kitchen sink being installed in a Mount Pleasant, TX home
DowntownSouthgateNorthwood

How sink installation runs in Mount Pleasant, TX

Kitchen installs cluster where kitchens are being refreshed: Downtown remodels, Southgate ranches getting a new sink and faucet, and new-build finishes in Northwood and Stone Briar. Bathroom sinks follow the same pattern, usually as part of a vanity replacement.

In older homes the drain under the sink can surprise you — a corroded trap or a galvanised line that needs replacing while the old sink is out. If your current sink only leaks underneath, a repair may be all it needs; our guide on how to unclog a kitchen sink drain safely helps you tell a clog from a failing trap.

  • Downtown Mount Pleasant, TX: Remodels in early-to-mid-20th-century kitchens. Old traps and galvanised drains are common, and we check them while the sink is out.
  • Southgate: 1970s brick ranches where kitchen refreshes are common. A new sink usually goes in with a new faucet and trap.
  • Northwood and Stone Briar: Newer north-side subdivisions, where sink installation work is usually on newer systems. Installs here are usually finish work on a new build or a kitchen refresh.
  • Lake Bob Sandlin area: Lakefront homes where sink installation installs happen between stays. We test every joint before we leave.
  • Rentals and turnovers: A new kitchen sink between tenancies lifts the whole room. We install it and check the disposal while we are there.
  • Trap first: A sink that weeps at the trap rots the cabinet within a year. We test every joint with the tap running before we call the job done.
See where we work
  • We walk the job and explain the plan
  • We protect counters and set up
  • We test, clean up, and walk you through

From problem to finished result

Example — a typical call. The stories below are illustrative examples of the kind of sink installation calls we take, not a record of a specific past job.

New kitchen sink being installed in a Mount Pleasant, TX home
IllustrativeThe thermal view for this sink installation job is generated from the photograph. It is not a measurement. Drag the handle to compare the before and after on this sink installation job, or use the arrow keys once it is focused.
  • Farmhouse sink in a Southgate kitchen

    Before: The homeowner had a farmhouse sink sitting in the box for three weeks. The counter was already installed and the opening was too small.

    After: We measured the template, trimmed the counter with a jigsaw and sealed the edge, set the sink, and connected the drain and supply lines. The sink sits flush and the water test showed no leaks.

    Wipe the silicone rim dry after use and check under the cabinet once a month for the first year.

  • Bathroom vanity swap in Downtown Mount Pleasant, TX

    Before: A cracked vanity sink was leaking into the cabinet, and the shutoff valves were frozen. The homeowner could not shut the water off to replace the sink.

    After: We replaced the shutoff valves with quarter-turn valves, set a new sink, and installed a new faucet. The water test ran clean. The cabinet dried out and the homeowner avoided a cabinet replacement.

    Turn the shutoff valves open and closed twice a year to keep them from seizing. Check the supply lines for cracks every six months.

  • Kitchen sink replacement in Northwood

    Before: A builder-grade stainless sink kept loosening and the drain was slow. The old sealant was failing and water was getting under the rim.

    After: We removed the old sink, cleaned the cutout, reset the basin with proper clips and silicone, and cleared the drain stub with a drain snake. The sink is solid and drains properly.

    Avoid standing on the sink rim and re-caulk the rim every five to seven years. Run hot water down the drain weekly to keep grease moving.

Sink problems we solve in Mount Pleasant

Most sink calls come down to a handful of problems. We diagnose the cause before quoting, so you are not paying to replace a sink when the drain line is the real issue.

  • Leak in cabinetOld sink leaking into the cabinetWater rots the cabinet base, warps the shelf, and can grow mold before the leak is spotted. A small drip turns into a big repair if it is ignored. We find the source, whether it is a failed seal, a cracked drain flange, or a bad supply line. If the sink is sound, we repair the connection. If the basin is cracked, we replace it and test every joint before we leave.
  • Slow drainNew sink does not drain rightStanding water in the basin breeds bacteria and leaves a ring. It usually means the P-trap is misaligned or the drain stub is partially clogged. We check the trap alignment, clear the drain stub with a drain snake, and make sure the vent is working. If the branch line is clogged, we clear it so the new sink drains fast.
  • Wrong cutoutCutout is wrong for the new sinkAn undersized or oversized cutout means the sink will not seal, and the countertop can crack at the edge. It is the most common reason a DIY sink install fails. We measure the cutout against the sink template before cutting. If the counter needs trimming, we do it with the right blade and seal the exposed edge. The sink sits flush and the rim seals.
  • Frozen valvesFrozen or leaking shutoff valvesOld valves that will not close mean you cannot shut the water off to work on the sink. A leaking valve drips into the cabinet every time the sink is used. We replace frozen or leaking shutoff valves with new quarter-turn valves. That gives you a clean shutoff for future repairs and stops the drip under the cabinet.

Why a proper sink install pays off

A level sink, dry cabinet, and drain that empties fast.

  • No leaks under the cabinet

    We pressure-test every supply line and run water through the drain before we leave. A new sink install from us includes checking the shutoff valves and resealing the rim so the seal holds through daily use.

  • Drains that actually drain

    A sink that pools water means the P-trap or drain stub is off. We align the drain, check the venting, and clear any hard water buildup in the tailpiece. If the old drain line is clogged, we can run a drain snake while we are there.

  • Correct cutout and fit

    Undermount and farmhouse sinks need the cutout measured to the template, not eyeballed. We check the countertop edge, the cabinet base, and the sink flange so the basin sits flush and the rim seals.

  • Code-correct connections

    We follow the 2024 International Plumbing Code adopted by the city (Ordinance 2026-2, effective 20 January 2026) on trap arms, venting, and shutoff placement. That matters if you ever sell the house or pull a permit. We also use push-to-connect or expansion fittings where they make sense and copper or PEX where the run calls for it.

What you receive with sink installation

Clear records from your sink installation job that you can keep and share.

Job photos

Before and after shots of the install

Parts list

What was replaced under the sink

Test record

Notes from the water test

Care sheet

Simple maintenance steps for the sink

Drop-in, undermount, and farmhouse sinks

The sink type decides how much cutout and mounting work the job takes.

Drop-in

Sits on top of the counter with a rim.

  • Simplest install
  • No cutout change
  • Seal under rim

Undermount

Mounts below the counter from underneath.

  • Clips hold basin
  • Cutout must be exact
  • Edge needs sealing

Farmhouse

Apron front sits proud of the cabinet.

  • Cutout is critical
  • Cabinet may need trim
  • Heavy basin support

What we work with

  • Copper pipe
  • PEX tubing
  • PVC pipe
  • CPVC pipe
  • Shutoff valves
  • Supply lines
  • Drain basket
  • Silicone

Service ZIP codes

A list like this tells people straight away whether we cover their street for sink installation. Not listed? Call and ask — it only takes a minute.

  • 75455
  • 75456

Areas we serve in Mount Pleasant, TX

Based in Mount Pleasant and covering the places around it. Pick one for local details.

View all service areas

What Mount Pleasant customers say

Excellence service and diagnosis with courtesy and understanding of the whole issue. Went well beyond the norm to assist whereby I was able to resolve the problem. Especially considering it was a Saturday morning service call Thank you so much for your expert advice. Hot water again, yeah!!!

SamE Embras Jr
5 stars · 2 years ago · Google review

The service I received from NTP Plumbing in April was Absolutely EXCEPTIONAL! The technician/plumber name was Jeremy. He took care of my pipe issues efficiently and treated me like I was family. Jeremy had excellent customer service/interpersonal skills and he made sure the work done was in the spirit of excellence. I would be remiss if I didn't mention the wonderful service I received from the owner, James. He was so welcoming and genuinely kind. James was able to get me scheduled in so that my plumbing would be taken care of in a timely manner. Thank you NTP Plumbing for all you do and especially for the things I don't see.

Ozie Hollingsworth
5 stars · 2 years ago · Google review

I recently used NTP for a clogged kitchen drain. The job took longer than anticipated but James honored his quote and the work is guaranteed for 30 days. I would highly recommend NTP for any plumbing needs you may have.

No Name
5 stars · 2 years ago · Google review

This review is about a used-appliance sale, a separate line of business — not plumbing work.

They sell used appliances as well, fyi they r super nice ND very great prices! They delivered my fridge same day we're quick and nice. Thank y'all so much for being so efficient!!

Brittney Moss
5 stars · 2 years ago · Google review

They were very professional and courtious. Fixed all my plumbing problems

Tim Griffin
5 stars · 4 years ago · Google review

4.8 out of 5 from 16 Google reviews — 15 five-star and 1 one-star. Read all reviews for NTP Plumbing on Google.

All reviews
4.8 out of 5 · 16 Google reviews

Frequently Asked Questions

Yes. We install the sink you supply, and we will tell you before we start if the drain position or the countertop cutout needs anything different.

Yes. The disposal and the dishwasher drain are connected as part of a kitchen sink install, and both are tested with the tap running.

Most installs are finished while we are there. If the trap or the drain underneath is corroded, the repair adds time — we will tell you what we find before we start.

Only if the sink was the problem. A slow sink drain is usually the trap or the drain line. We check the drain before recommending a new sink.

Get sink installation in Mount Pleasant, TX scheduled

Call (903) 350-9085 and tell us which sink you want fitted. We will set the trap, connect the disposal, and test every joint. Open 24 hours, Monday–Sunday.

Get in Touch with NTP Plumbing

Call (903) 350-9085 any time — NTP Plumbing is open 24 hours, Monday–Sunday. Tell us what you are seeing and we will talk you through shutting the water off if you need to. We serve Mount Pleasant, TX, including ZIP codes 75455 and 75456.

Thanks. Your request is in and the team will follow up shortly.