Shower installation in Mount Pleasant, TX, fitted and tested

Shower installation is the professional fitting of a new shower in a Mount Pleasant, TX bathroom, with valves and drainage tested. A new shower should hold its temperature, drain cleanly, and never leak into the wall behind it. NTP Plumbing installs showers across Mount Pleasant, TX — valve, trim and drain set, temperature tested before we leave. Open 24 hours, Monday through Sunday.

New shower being installed in a Mount Pleasant, TX bathroomNew showerValve setTemperature tested
  • Drop cloths downFloors and fixtures covered
  • Debris bagged dailyOld unit hauled off
  • Water shut off firstNo surprise spray
  • Walkthrough at finishValve and shutoff shown

What's Included in a Shower Installation

Every install includes the plumbing work, the waterproofing, and the cleanup. Here's what's covered in a standard scope, and what we quote separately if your bathroom needs it.

New shower being installed in a Mount Pleasant, TX bathroom
  • Tear-Out and Haul-Off

    We remove the old tub or shower unit, the surround, and the valve trim, and we haul it all away. That includes the pan, the door, and any tile or fiberglass. You don't need to rent a dumpster or make a trip to the landfill.

  • Drain and Valve Rough-In

    We set a new drain and valve body at the correct height, replace the supply lines with PEX tubing or copper, and tie the vent to code. If the existing drain line has hard water buildup or root intrusion, we clear it before the new pan goes down.

  • Waterproofing and Flood Test

    The pan goes on a level mortar bed with a sealed drain, and we apply waterproof membrane up the walls. Then we fill the pan and let it sit 24 hours. If it holds, we move to finish. If not, we fix it before tile goes up.

  • Surround, Trim, and Showerhead

    We install your chosen surround, tile, or prefab unit, then set the valve trim, showerhead, and door or rod. We set the temperature limit stop and run the shower to check for drips behind the wall.

  • Final Cleanup and Walkthrough

    We sweep, wipe down the new shower, and walk you through the valve, the drain screen, and the shutoff. You get the old unit gone, the new one running, and a clear explanation of how to take care of it.

Homes and rentals

A remodel and a new-build install are different jobs — one starts with an old shower and a wall of unknown condition, the other with a fresh rough-in — but the checks at the end are the same in a home and a rental. What changes is the access, the schedule, and who needs the paperwork for a shower installation job.

For Homes and Rentals

We install showers in houses, duplexes, and rental units across Mount Pleasant. We schedule around your workday and keep the bathroom sink and toilet usable through most of the job.

  • Cracked pan or surround
  • Tub-to-walk-in conversion
  • Valve that won't hold temperature

For rentals and property managers

We handle multi-unit shower replacements for rental properties. We coordinate tenant access and document the scope per unit.

  • Multi-unit replacement schedules
  • Tenant access coordination
  • Written scope per unit

What shower installation in Mount Pleasant, TX actually involves

A plain-language look at what Shower Installation involves and when it is needed. The City of Mount Pleasant charges a $75 residential plumbing permit fee where a permit is required (inside city limits) — that is a City fee, not our price.

See how it works

Installing a shower means setting the valve in the wall at the right depth, connecting the supply lines, fitting the trim and head, and testing the temperature through its full range. The drain gets checked too — a new shower on a slow drain is a flood waiting for the first long shower. Then the wall is closed and every joint is watched for a weep.

Most installs in Mount Pleasant, TX are bathroom remodels in Downtown homes and Southgate ranches, and finish work in Northwood, Stone Briar and Deer Park Estates new builds. In older homes the supply lines behind the wall are often galvanised and narrowing; we check them while the wall is open, because that is the only cheap moment to deal with them. Shower installation work follows the 2024 International Plumbing Code adopted by the city.

A shower is a valve in a wall. Get the valve right and the rest follows.

New shower being installed in a Mount Pleasant, TX bathroom
What it is
Setting a new shower valve, trim and head, with the drain checked and the temperature tested.
When you need it
A remodel, a failed valve body, or a new bathroom going in.
What to expect
Steady temperature, a clean drain, and a wall that stays dry.

What to Expect on Install Day

Every shower install follows the same five stages. Here is what happens at each stage, from first look to final test.

  1. On-Site Assessment

    We walk the bathroom, measure the alcove, check the shutoff valves, and inspect the drain with a sewer camera if the line is old. You get a written scope and a quote before we touch a tool.

    • Measure alcove
    • Check valves
    • Camera drain
    New shower being installed in a Mount Pleasant, TX bathroom
  2. Tear-Out and Rough-In

    We shut off the water, remove the old tub or shower, and haul it out. Then we cut back the supply lines, solder or crimp new PEX tubing, and set the drain and valve body at the right height.

    • Shut off water
    • Tear out old
    • Set rough-in
    New shower being installed in a Mount Pleasant, TX bathroom
  3. Waterproofing and Pan

    The pan goes down on a level mortar bed, the drain gets sealed, and we roll on waterproof membrane up the walls to 6 inches above the curb. We flood-test the pan for 24 hours before any tile or surround goes in. This is the step most rushed jobs skip.

    • Level pan
    • Seal drain
    • Flood test
    New shower being installed in a Mount Pleasant, TX bathroom
  4. Finish and Trim

    Tile, surround panels, or a prefab unit goes in, followed by the valve trim, showerhead, and door or curtain rod. We check the temperature limit stop so nobody gets scalded, and we run the shower to confirm no drips behind the wall.

    • Set surround
    • Install trim
    • Run shower
    New shower being installed in a Mount Pleasant, TX bathroom
  5. Cleanup and Walkthrough

    We haul off the old unit, sweep, and wipe down the new shower. Then we walk you through the valve, the drain screen, and how to shut the water off if you ever need to.

    • Haul debris
    • Wipe down
    • Show shutoff
    New shower being installed in a Mount Pleasant, TX bathroom

Tools and Methods We Use

Move across a circle, or focus it and press Enter, for an illustrative thermal view of this shower installation photograph.

  • New shower being installed in a Mount Pleasant, TX bathroom

    PEX Crimping Tool

    Used to make secure connections on PEX tubing supply lines. A proper crimp ring is faster and more reliable than a solder joint in tight shower walls.

  • Plumber soldering a copper pipe joint under a kitchen sink in a Mount Pleasant, TX home

    Soldering Torch

    For copper pipe connections where code or existing plumbing requires soldered joints. We use it on valve bodies and supply stubs that need a permanent connection.

  • Plumber running a sewer camera inspection in Mount Pleasant, TX

    Sewer Camera

    We run it down the shower drain before install to check for root intrusion, scale, or a collapsed section. It tells us whether the drain is sound before the new pan goes down.

  • Plumber cleaning a clogged drain in a Mount Pleasant, TX home

    Hydro Jetter

    Clears hard water scale and soap scum from drain lines that a snake can't reach. We use it when the shower drain is slow but not blocked.

  • Plumber using leak detection equipment in a Mount Pleasant, TX home

    Leak Detection Microphone

    Finds hidden leaks behind walls or under the pan without tearing everything out. It's how we confirm a leak source before we start cutting.

Thermal views are illustrative, generated from photographs of shower installation work in Mount Pleasant, TX.

Methods

  • Pressure Gauge

    Checks water pressure at the shower valve. High pressure can blow a cartridge; low pressure means the valve or supply line is restricted. We test before and after install.

  • Pipe Wrench

    For threaded connections on older drain and supply lines. A proper pipe wrench gets a drain assembly tight without cracking the fitting.

  • Flood Testing the Pan

    We fill the new shower pan with water and let it sit 24 hours before any tile or surround goes in. If the waterproofing holds, the shower won't leak. If it doesn't, we fix it before finish. This is the single most important step in a shower install.

  • Drain Sizing

    We size the shower drain and vent to the 2024 International Plumbing Code adopted by the city (Ordinance 2026-2, effective 20 January 2026). That means the drain is large enough for the showerhead flow and the vent is tied correctly so the drain doesn't gurgle.

  • WaterSense Fixture Selection

    We install EPA WaterSense-rated showerheads and valves. They hold pressure while using less water, which matters in Mount Pleasant, where water bills climb in summer.

  • Temperature Limit Stop Setting

    Every valve we install gets the temperature limit stop set so the water can't exceed a safe temperature. It's a small adjustment that prevents scalding, especially in homes with kids or older adults.

When a New Shower Makes Sense

New shower being installed in a Mount Pleasant, TX bathroom

Bathroom remodel

A remodel needs a new shower where the old tub-shower was.

We set the valve at the right depth, connected the supplies, fitted the trim and head, and tested the temperature through its full range.

Outcome: A steady, hot shower with a dry wall behind it.

New shower being installed in a Mount Pleasant, TX bathroom

Failed valve body

The old valve leaked inside the wall and the cartridge would not fix it.

We opened the wall, replaced the valve body, and closed it back up. The new valve was tested before the tile went back.

Outcome: A shower that holds temperature and stays dry inside the wall.

New shower being installed in a Mount Pleasant, TX bathroom

New build finish

A new-build bathroom needs its shower set.

We fitted the valve, trim and head on the new rough-in and tested the drain with a long run of water.

Outcome: A finished bathroom, tested and dry.

New shower being installed in a Mount Pleasant, TX bathroom

Low pressure fix

A new shower was wanted, but the pressure was the real problem.

We checked the pressure first and found the galvanised run behind the wall. The run was replaced while the wall was open, then the new shower went in.

Outcome: A new shower with the pressure to run it properly.

New shower being installed in a Mount Pleasant, TX bathroom
DowntownSouthgateNorthwood

How shower installation runs in Mount Pleasant, TX

Remodel installs cluster in the older stock: Downtown bathrooms from the 1940s–1980s and Southgate's 1970s ranches, where a new shower usually means opening the wall and finding the original valve and galvanised runs behind it. New-build shower installation installs happen in Northwood, Stone Briar and Deer Park Estates, where the rough-in is new and the job is straightforward.

Country Club Estates and Greenhill Park custom homes often want larger showers with more than one head, which means the valve and the supply sizing matter more. For a wider look at where new shower plumbing goes in around town, see our post on the best neighborhoods in Mount Pleasant, TX for new plumbing installations.

  • Downtown Mount Pleasant, TX: Remodels in early-to-mid-20th-century bathrooms. Opening the wall usually finds the original valve and galvanised runs behind it.
  • Southgate: 1970s brick ranches where bathroom refreshes are common. A new shower usually goes in with the valve and the drain checked.
  • Northwood and Stone Briar: Newer north-side subdivisions, where shower installation installs are usually finish work on a new build or a bathroom refresh.
  • Country Club Estates: Golf-course custom homes with larger showers. Valve choice and supply sizing matter more with multiple heads.
  • Lake Bob Sandlin area: Lakefront homes where shower installation installs happen between stays. We test temperature and drainage before we leave.
  • Supply lines behind the wall: In older homes the runs are often galvanised and narrowing. We check them while the wall is open — the only cheap moment to deal with them.
See where we work
  • We walk the bathroom and measure the alcove.
  • Drop cloths go down and the water is shut off.
  • We test the shower and show you the shutoff.

From problem to finished result

Example — a typical call. The stories below are illustrative examples of the kind of shower installation calls we take, not a record of a specific past job.

New shower being installed in a Mount Pleasant, TX bathroom
IllustrativeThe thermal view for this shower installation job is generated from the photograph. It is not a measurement. Drag the handle to compare the before and after on this shower installation job, or use the arrow keys once it is focused.
  • Cracked Pan to Walk-In Shower

    Before: A 1990s fiberglass shower pan had cracked near the drain, and water was staining the ceiling in the dining room below. The surround was yellowed and the valve cartridge was failing, so the temperature swung hot and cold.

    After: We removed the old unit, replaced the subfloor section, and installed a low-threshold walk-in pan with tile surround and a new pressure-balance valve. The flood test held for 24 hours, and the ceiling below stayed dry.

    Wipe the pan weekly and run the fan after showers. Check the drain screen monthly and clear hair before it reaches the trap.

  • Tub Conversion for Aging in Place

    Before: A homeowner needed a safer shower for a parent using a walker. The existing tub-shower combo had a 15-inch tub wall to step over and no grab bars. The drain was in the wrong spot for a walk-in pan.

    After: We moved the drain, framed blocking for grab bars, and installed a low-threshold pan with a bench and a handheld showerhead. The valve was set at a reachable height, and the temperature limit stop was set to prevent scalding.

    Check the grab-bar screws every six months and keep the pan free of soap film. Run the handheld showerhead through its full range monthly to keep the hose from stiffening.

  • Rental Unit Shower Replacement

    Before: Two rental units had cracked surrounds and slow drains that tenants had complained about for months. The valves were original builder-grade and one wouldn't hold temperature. The property manager needed both units done quickly.

    After: We replaced both showers on consecutive days, ran a camera down each drain, and replaced the valves while the walls were open. The property manager had a written scope for each.

    Replace the drain screen every year and have the drain snaked annually. Check the caulk line at the pan edge each spring and re-caulk if it pulls away.

Shower Problems We Fix Before They Spread

Most shower calls start small and get expensive fast. Here are the problems we see most often in Mount Pleasant, and what happens if they're ignored.

  • Cracked pan leakCracked fiberglass pan leaking into the ceiling belowWater rots the subfloor, stains drywall, and can grow mold inside the wall cavity. We remove the failed pan, inspect the subfloor for rot, and install a new pan on a level mortar bed with a sealed drain. We flood-test it for 24 hours before any finish goes down, so you know the leak is gone.
  • Valve temperature swingShower valve that won't hold temperatureA valve that swings from scalding to cold is a burn risk, especially in homes with kids or older adults. It usually means the cartridge or pressure-balancing spool has failed. We replace the valve cartridge or the whole valve body if the seat is corroded. We set the temperature limit stop so the water can't exceed a safe range, and we test it at the showerhead before we leave.
  • Slow drain backupSlow drain that backs up even after snakingA shower that pools around your feet is usually a sign of hard water buildup or a partially collapsed drain line. Snaking clears hair but not scale or a broken pipe. We run a sewer camera down the line to see what's actually blocking it. If it's scale, we hydro jet it. If it's a broken section, we repair or replace that section before the new shower drain ties in.
  • Mold behind wallMold and mildew behind the shower wallMold behind tile or a surround means water has been getting in for a while. It can spread into adjacent rooms and affect indoor air quality. We tear out the affected wall, treat the framing, and rebuild with proper waterproofing membrane and backer board. We don't cover mold with new tile. We fix the source, then finish the shower.

Why Homeowners Upgrade Their Shower

A shower that drains fast, holds temperature, and stays dry below.

  • No More Leaks Below

    A failed pan or missing waterproofing sends water into your subfloor and ceiling. We set the pan on a level bed, seal the drain with a new wax ring or gasket, and flood-test before tile. That is the difference between a shower that stays dry and one that leaks.

  • Better Pressure, Less Waste

    Old shower valves clog with mineral scale and cut your flow to a trickle. We install EPA WaterSense-rated fixtures that hold pressure without wasting water.

  • Safer Step-In Access

    A walk-in shower removes the tub wall you have to climb over. Low-threshold pans and grab-bar-ready blocking make the shower safer for older family members and anyone recovering from surgery. We frame the blocking during rough-in so it's there when you need it.

  • Code-Correct Drain and Vent

    A shower drain has to be sized and vented to the 2024 International Plumbing Code adopted by the city (Ordinance 2026-2, effective 20 January 2026), or it gurgles and drains slow. We run the drain snake and sewer camera first, confirm the slope, and tie the vent correctly so the shower drains fast.

What you receive with shower installation

Clear records from your shower installation job that you can keep and share.

Written scope

What's covered before work starts

Flood test log

Date and result recorded

Photo record

Rough-in and finish photos

Walkthrough note

Valve and shutoff explained

Pan types and what they mean for your floor

The pan you choose affects the drain, the floor height, and how the shower feels underfoot.

Prefab pan

A molded pan that sits on a mortar bed.

  • Fastest install
  • Lowest cost
  • Limited sizes

Tile pan

A custom pan built and waterproofed on site.

  • Custom size
  • Tile finish
  • Longer cure time

Low-threshold

A pan with a low curb for easier step-in.

  • Safer access
  • Grab-bar ready
  • Drain may move

Materials and fixtures we work with

  • PEX tubing
  • Copper pipe
  • PVC drain
  • Shower valve
  • Valve trim
  • Showerhead
  • push-to-connect fitting
  • Waterproof membrane

Service ZIP codes

A list like this tells people straight away whether we cover their street for shower installation. Not listed? Call and ask — it only takes a minute.

  • 75455
  • 75456

Areas we serve in Mount Pleasant, TX

Based in Mount Pleasant and covering the places around it. Pick one for local details.

View all service areas

What Mount Pleasant Customers Say

Excellence service and diagnosis with courtesy and understanding of the whole issue. Went well beyond the norm to assist whereby I was able to resolve the problem. Especially considering it was a Saturday morning service call Thank you so much for your expert advice. Hot water again, yeah!!!

SamE Embras Jr
5 stars · 2 years ago · Google review

The service I received from NTP Plumbing in April was Absolutely EXCEPTIONAL! The technician/plumber name was Jeremy. He took care of my pipe issues efficiently and treated me like I was family. Jeremy had excellent customer service/interpersonal skills and he made sure the work done was in the spirit of excellence. I would be remiss if I didn't mention the wonderful service I received from the owner, James. He was so welcoming and genuinely kind. James was able to get me scheduled in so that my plumbing would be taken care of in a timely manner. Thank you NTP Plumbing for all you do and especially for the things I don't see.

Ozie Hollingsworth
5 stars · 2 years ago · Google review

I recently used NTP for a clogged kitchen drain. The job took longer than anticipated but James honored his quote and the work is guaranteed for 30 days. I would highly recommend NTP for any plumbing needs you may have.

No Name
5 stars · 2 years ago · Google review

This review is about a used-appliance sale, a separate line of business — not plumbing work.

They sell used appliances as well, fyi they r super nice ND very great prices! They delivered my fridge same day we're quick and nice. Thank y'all so much for being so efficient!!

Brittney Moss
5 stars · 2 years ago · Google review

They were very professional and courtious. Fixed all my plumbing problems

Tim Griffin
5 stars · 4 years ago · Google review

4.8 out of 5 from 16 Google reviews — 15 five-star and 1 one-star. Read all reviews for NTP Plumbing on Google.

All reviews
4.8 out of 5 · 16 Google reviews

Common Questions About Shower Installation

Most installs are finished while we are there when the rough-in is already there. A remodel that needs the wall opened and the valve moved takes longer — we will tell you what we find before we start.

Yes. We install the shower and valve you supply, and we will tell you before we start if the rough-in or the supply connections need anything different.

Only if the shower was the problem. In older Mount Pleasant, TX homes the cause is often a galvanised supply line narrowing with corrosion. We check the pressure before recommending a new shower.

Yes. A new shower on a slow drain floods on the first long shower. We check the drain and the trap as part of the install.

Get shower installation in Mount Pleasant, TX scheduled

Call (903) 350-9085 and tell us what shower you want fitted. We will set the valve, test the temperature, and check the drain. Open 24 hours, Monday–Sunday.

Get in Touch with NTP Plumbing

Call (903) 350-9085 any time — NTP Plumbing is open 24 hours, Monday–Sunday. Tell us what you are seeing and we will talk you through shutting the water off if you need to. We serve Mount Pleasant, TX, including ZIP codes 75455 and 75456.

Thanks. Your request is in and the team will follow up shortly.