For Homes and Rentals
We install kitchen and bathroom faucets in houses, condos, and rentals. We check the shutoff valves and supply lines so the new fixture runs leak-free.
- Worn kitchen faucet
- Corroded bathroom handles
- Loose faucet base
Faucet installation is the professional fitting of a new kitchen or bathroom faucet in a Mount Pleasant, TX home, with supply lines and shutoffs checked. A new faucet should feel solid, shut off cleanly, and not leak at the base a month later. NTP Plumbing installs kitchen and bathroom faucets across Mount Pleasant, TX, with new supply lines and shutoffs checked as part of the job. Open 24 hours, Monday through Sunday.
New faucetLines checkedTested at pressureEvery install includes the basics that make a faucet last: removal of the old fixture, new supply lines, fresh seals, and a full leak test. If we find worn shutoff valves or a damaged drain assembly, we quote the added work before we do it.

We shut off the water, drain the lines, and remove the old faucet, supply lines, and drain assembly. We protect the sink and cabinet floor and haul the old fixture away with us.
We install new braided stainless supply lines sized to the fixture. Old lines are a common leak point, so replacing them during the install is cheap insurance against a cabinet full of water.
We test the angle stops under the sink. If they will not close or are corroded, we replace them with new quarter-turn valves so you can shut the water off in an emergency.
We connect the drain assembly and sprayer hose, check the gaskets, and test for leaks. On kitchen faucets, we confirm the sprayer retracts and the diverter works.
We run hot and cold water, check every connection, and use a pressure gauge to confirm house pressure is in range. We do not leave until the sink is dry under the cabinet.
A kitchen faucet and a bathroom faucet install differently — hole spacing, spout reach, and supply layout all change with the sink — but the checks at the end are the same in a home and a rental. What changes is the access, the schedule, and who needs the paperwork for a faucet installation job.
We install kitchen and bathroom faucets in houses, condos, and rentals. We check the shutoff valves and supply lines so the new fixture runs leak-free.
We handle faucet replacement in rental units. We schedule around tenant access and document the work for the property file.
A plain-language look at what Faucet Installation involves and when it is needed. The City of Mount Pleasant charges a $75 residential plumbing permit fee where a permit is required (inside city limits) — that is a City fee, not our price.
See how it worksInstalling a faucet is more than swapping the fixture on the sink. The old faucet comes out, the deck is cleaned and checked for damage, the new faucet is set with the right gasket and sealant, and the supply lines and shutoffs are checked — or replaced if they will not close. Then the water goes back on and every joint is watched for a weep.
The jobs we see most are kitchen upgrades in Southgate and Downtown remodels, and bathroom refreshes in Northwood and Stone Briar. In older Mount Pleasant, TX homes the shutoffs under the sink are often original and seized; replacing them at install time is cheaper than an emergency call later. We fit the faucet you supply or one you ask us to bring, and we never push a particular make.
A faucet is only as good as the shutoff and supply line behind it.

We keep the job simple and predictable. Here is what happens from the first call to the final test, whether it is a single bathroom faucet or a full kitchen upgrade.
You call (903) 350-9085 and tell us what you have: the fixture, the sink type, and whether the old faucet is leaking. We ask about shutoff valves and supply lines because those often need replacing too. Most calls take a few minutes, and we give you a quote before we schedule.
On arrival we shut off the water at the angle stops or the main, then drain the lines. We lay a towel and a bucket under the sink and pull the old faucet, supply lines, and drain assembly. If a shutoff valve will not close, we replace it while we are in there.
We clean the mounting surface, check the hole spacing, and dry-fit the new faucet. On a bathroom install, that means checking the 4-inch or 8-inch centers and making sure the new spout clears the sink bowl. We set the gasket and align the handle positions before anything gets tightened.
We connect the supply lines with new braided hoses, apply Teflon tape to the threads, and tighten the mounting nuts evenly. The drain and sprayer get connected and tested. We use a pressure gauge to confirm the house pressure is in range, because high pressure is a common cause of premature faucet failure.
We run hot and cold, check for drips at every connection, and test the sprayer and drain. Then we wipe down the sink, haul off the old fixture, and walk you through what we did.
Move across a circle, or focus it and press Enter, for an illustrative thermal view of this faucet installation photograph.

Reaches the mounting nuts behind the sink bowl where a regular wrench will not fit. It is the difference between a clean removal and a stripped nut.

Used on shutoff valves and supply fittings when they are stuck. We use it carefully so we do not twist the pipe behind the wall.

Seals threaded connections on supply lines and shutoff valves. The right amount prevents leaks without cracking plastic fittings.

Checks house pressure at the hose bibb. High pressure is a common cause of faucet and supply line failure.

Used when we replace a section of supply pipe with PEX tubing. It makes a code-correct crimp that will not leak behind the wall.
Thermal views are illustrative, generated from photographs of faucet installation work in Mount Pleasant, TX.
For copper pipe repairs when a supply line needs to be cut and re-sweated. We use it with a heat shield to protect the cabinet and framing.
We follow the IPC for supply connections, backflow protection, and drain assembly. That means the install passes inspection and works the way the manufacturer intended.
Faucet makers publish torque values for mounting nuts and supply connections. We follow them so we do not crack porcelain sinks or strip brass threads.
After the install we run the faucet and check every connection with a dry paper towel. Any moisture means we tighten or reseal before we call the job done.
We replace old supply lines as part of the install unless they are clearly new. Braided stainless lines cost little and prevent the most common under-sink leak.

A kitchen remodel needs a new faucet on a fresh sink.
We set the faucet with the right gasket, fitted new braided supply lines and stops, and tested every joint at full pressure.
Outcome: A solid mount, no weeps, and shutoffs that close.

A vanity replacement needs new faucets to match.
We fitted both basin faucets, replaced the tired stops underneath, and checked the trap while the cabinet was open.
Outcome: A finished vanity with dry connections and working shutoffs.

The old faucet came off, but the shutoff underneath would not turn.
We replaced the seized stop before fitting the new faucet, so the next repair will not need the main shut off.
Outcome: A new faucet on a supply that can actually be isolated.

A rental kitchen needs a new faucet between tenancies.
We coordinated with the property manager, fitted the faucet and new supply lines, and left the old one for disposal.
Outcome: A fresh kitchen tap ready for the next tenant.

Kitchen faucet installs are the most common, and they cluster where kitchens are being refreshed: Downtown remodels, Southgate ranches getting a new sink, and new-build finishes in Northwood and Stone Briar. Bathroom faucets follow the same pattern, usually as part of a vanity replacement.
In older homes the deck or the shutoffs can surprise you — a corroded stop or a pitted sink deck turns a simple swap into a repair as well, and we will tell you before we start. If your current faucet is only dripping, a repair may be all it needs; our guide on how to fix a dripping faucet in your Mount Pleasant, TX home helps you tell the difference.
Example — a typical call. The stories below are illustrative examples of the kind of faucet installation calls we take, not a record of a specific past job.

Before: A kitchen faucet dripped constantly and the base was loose. The shutoff valves were original and would not close all the way, so the homeowner had to shut off the main to stop the water.
After: We replaced both angle stops with quarter-turn valves, installed new braided supply lines, and set a new pull-down faucet. The drip stopped, the base is solid, and the homeowner can shut off the water under the sink.
Wipe the faucet dry after use and check the aerator every six months. In hard water, soak the aerator in vinegar to clear scale.
Before: A bathroom faucet had corroded handles and a cracked supply line that left a small puddle in the vanity cabinet. The pop-up drain would not seal, so the sink drained slowly.
After: We installed a new widespread faucet, replaced both supply lines, and installed a new drain assembly. The handles turn smoothly, the sink drains fast, and the cabinet stays dry.
Check under the sink once a month for moisture. Replace the supply lines every five to seven years even if they look fine.
Before: A rental unit had a builder-grade faucet with a broken sprayer and a shutoff valve that was stuck open.
After: We replaced the faucet, the shutoff valve, and the supply lines while we were there. The unit was ready for the new tenant.
Tell tenants where the shutoff valves are and check the faucet at each turnover. A quick look saves a big repair later.
Sometimes a faucet just needs a cartridge. Other times the fixture is worn out and a replacement is the smarter spend. Here is what we see most often in Mount Pleasant.
A faucet that runs clean, seals tight, and shuts off when you need it to.
A leaky faucet connection can rot a cabinet floor in a season. We pressure-test every supply line and drain fitting before we pack up, so you are not mopping up water a week later. That test catches the small stuff early.
Clogged aerators and undersized supply lines cut flow to a trickle. We match the supply line size to the fixture and flush the lines before final hookup, so your new faucet runs at the pressure the manufacturer intended.
Texas follows the International Plumbing Code in most jurisdictions, and that means proper backflow protection and no cross-connections. We install faucets with the right air gap and vacuum breaker where required, which matters most on outdoor hose bibbs and pull-out sprayers.
Overtightened mounting nuts crack porcelain sinks and strip brass threads. We torque to spec and use the right washers and gaskets, which is why a properly installed faucet runs for years before the cartridge needs attention.
Clear records from your faucet installation job that you can keep and share.
What was installed and tested
Supplies and valves replaced
Pressure and leak check results
Simple maintenance steps
The faucet style you choose changes the install time, the parts needed, and how the fixture holds up over time.
One lever controls hot and cold
Separate hot and cold handles
Sprayer built into the spout
A list like this tells people straight away whether we cover their street for faucet installation. Not listed? Call and ask — it only takes a minute.
Based in Mount Pleasant and covering the places around it. Pick one for local details.
Yes. We fit the faucet you supply, and we will tell you before we start if anything about it — the deck holes, the supply connections — needs an adapter or a change.
We check them on every install. If the lines are old, stiff or weeping, or the shutoffs will not close, we recommend replacing them while the water is already off.
Most installs are finished while we are there. Older homes can take longer if the shutoffs are seized or the deck needs work — we will tell you what we find before we start.
We test every joint at full pressure before we leave, and we watch the base and the connections while the water runs. If anything weeps during a faucet installation job, it gets fixed on the spot.
Other services from the same team.
Call (903) 350-9085 and tell us which faucet you want fitted. We will check the deck, the lines and the shutoffs, and test everything before we leave. Open 24 hours, Monday–Sunday.
Call (903) 350-9085 any time — NTP Plumbing is open 24 hours, Monday–Sunday. Tell us what you are seeing and we will talk you through shutting the water off if you need to. We serve Mount Pleasant, TX, including ZIP codes 75455 and 75456.